Archive for 'May 2012'

You make MEMS. Should you make sensor fusion software?

May 25, 2012 10:04 AM by Solid State Technology


May 25, 2012 -- Sensor fusion is a software solution to improve the operation of multiple micro electro mechanical system (MEMS) sensors in concert. Through sensor fusion, gyroscopes, accelerometers, pressure sensors, magnetometers, and other devices can be operated together to compensate for inherent sensor weaknesses and enable new precision and new applications. “Combination sensors are a marginal player now but expected to penetrate 40% of the $2.7 billion consumer inertial market and 12%+ of the $1.1 billion automotive inertial market by 2016,” according to Yole Développement .

With 5-10 MEMS devices integrated into every smartphone, tablet, and other electronics, sensor fusion can be a differentiating factor in product capabilities and performance. No surprise then that so many companies -- software suppliers and MEMS makers -- are increasing their efforts in sensor fusion development.

I recently spoke with Leopold Beer, marketing leader at Bosch Sensortec, the consumer MEMS division of Bosch, about a new inertial measurement unit that was developed concurrently with gen-2 of Bosch’s sensor fusion software, FusionLib. “The hardware and software are not 2 separate new products,” said Beer, “they work together. The physics of sensing are the same as they were 10 years ago,” he added, “we can provide better products because of miniaturization and sensor fusion.”

MEMS manufacturers are the best companies to do sensor fusion development, not software suppliers, because they understand the performance and physics of each MEMS device intimately, Beer said. MEMS are a highly varied group of semiconductors, with little standardization from one to the next. And every MEMS sensor performs differently. “When designing a system using multiple MEMS sensors, it is important to understand the advantages and disadvantages of accelerometers, gyroscopes, magnetometers, and pressure sensors,” said Jay Esfanyari et al, STMicroelectronics, in our July 2011 cover article, “Solutions for MEMS sensor fusion.” STMicroelectronics is a major manufacturer of MEMS components. Beer envisions handsets and other electronics that use device-specific sensor fusion to optimize and calibrate MEMS performance, and some level of hardware-agnostic sensor fusion that connects all the sensors in a device, if they are not all from the same manufacturer. Detailed knowledge of sensor fusion techniques is also important to the system as a whole, because some algorithms lead to higher power consumption than others, and some MEMS devices draw more power than others. A sensor fusion strategy should be selected for, in addition to improving performance, its impact on system-level power consumption, noted Esfandyari et al.

Another group of companies provides sensor fusion software -- hardware-agnostic software developers. Hillcrest Labs and Sensor Platforms both released sensor fusion programs recently . Motion control software can “limit sensor choice, integration flexibility, and performance” in the system design, said Chad Lucien, senior vice president of sales and marketing for Hillcrest Labs. The major benefit of software-company sensor fusion is that MEMS can come from any manufacturer in the marketplace. For high-volume applications that require secondary sourcing of components, a hardware-agnostic sensor fusion platform eliminates supply bottlenecks.

The MEMS supply chain will change, according to Yole, as companies "figure out how best to compete and cooperate for the much bigger business of integrating the silicon sensors into useful functions...Players in the MEMS industry can compensate for price declines by selling high-value solutions that include more software content. Higher-value software calculations might require an MCU, not the usual ASIC. Makers of microcontrollers, software, and subsystems will start to take over more of the sensor management.”

As MEMS become more pervasive in everyday life, industrial and military instruments, vehicles, and other applications, sensor fusion will be an increasingly important consideration, and a potential differentiator for MEMS manufacturers.

--Meredith Courtemanche, digital media editor, meredithc@pennwell.com




Entegris tour covers the leading edge of filtration, 450mm, and the importance of collaboration

May 2, 2012 10:46 AM by Solid State Technology


May 2, 2012 -- Solid State Technology recently visited Entegris’ Billerica, MA, location to discuss the contamination challenges of leading-edge semiconductor fabs, the progress made or not made by the semiconductor industry on 450mm, and Entegris’ new i2M Center for Advanced Materials Science. We poked our heads into various engineering labs to watch filter development in action, see how filter membranes are folded or stacked for best contamination control and materials throughput, and learn about new materials that create cleaner fab environments.

Semiconductor wafer fabs are the leading edge for contamination control and sterility across any industry sector, said John Puglia, Ph.D., director of research development and engineering at Entegris. “I could bring a semiconductor wafer into an operating theater in a hospital, but if I tried to bring it back into a wafer fab, they wouldn’t let me past the parking lot!” Puglia said.

Device nodes are so fine now, that things “we took for granted” in the past now cause problems, he added. Contamination can occur from the polymers in the filter, which prompted Entegris to change from commodity to engineered resins for its raw materials. The lining in a bulk chemical tank far upstream matters now at the wafer level. Gas filtration is needed in front opening unified pods (FOUPs) to prevent moisture contamination of wafers. People are walking sources of fab contamination as well, despite cleanroom attire.

This ever-increasing attention to contaminants at the leading edge informs products for mature nodes as well. Yields can be improved at the larger nodes with enhanced air and liquid filtration, and the data from these high-volume applications will inform leading-edge product development.

Jennifer Braggin, strategic applications technologist at Entegris, says the way to move forward and resolve contamination control/throughput challenges is through more and more collaboration. Customers request it, she said. Working with research organizations like imec directly benefits Entegris’ product lines, today and for future products, she added, praising the open environment at imec that allows suppliers and chipmakers from all steps in the chain to interact.

We also had a chance to consider 450mm while visiting Entegris. The size of the 450mm opportunity is smaller than the opportunity at 300mm was, which was in turn smaller than the opportunity at 200mm, said Bertrand Loy, EVP and COO at Entegris. Meaning, equipment suppliers will not see as many orders for 450mm tools as they did in the previous wafer size transitions. A small number of chip makers dominate the industry now, however, and if those suppliers begin to really demand 450mm, equipment makers will need to support the move. Referring back to the chip fab/supply chain collaboration that Braggin described, the team at Entegris said consolidation in the chip manufacturing sector actually improves supply chain collaboration, as tool suppliers and infrastructure support companies build R&D teams around “mega companies” making semiconductors.

We’ll be back to visit Entegris when their new i2M Center for Advanced Materials Science goes up nearby in Bedford, MA. Some of the filtration labs we saw on this trip will move into the new location, joining -- for intra-supplier collaboration -- their colleagues working on electrostatic wafer clamps (E-Chucks) and proprietary advanced low-temperature coatings. You can read about the Entegris i2M Center for Advanced Materials Science here.
-- Meredith Courtemanche, digital media editor, Solid State Technology , meredithc@pennwell.com